Welcome, Huatui Group

HUATUI

Integrity Quality
NEWS
  • Holiday Announcement of 2018 Spring Festival
  • AC Solenoid and DC solenoid
  • Irrigation Control Systems
  • What is solenoid parameters?
  • 05,JAN,2018 HUATUI GROUP- Company Day
  • Happy New Year-HUATUI
  • How to Make Solenoid Coil?
  • Merry Christmas
  • Guide To Sprinkler Valve Repair 1: Valve Not Turning On
  • What is the Difference Between Rebuilt Engines and Remanufactured Engines?
  • How to Replace a Sprinkler Valve?
  • How to Find A Sprinkler Valve?
  • Asia-Pacific Automotive Solenoid Market 2017- Robert Bosch, Hitachi, Mitsubishi Electric, Continental
  • Tools 2:Irrigation Glossary A to the C
  • What is remanufacturing?
  • Automechanika Shanghai 2017
  • Symptoms of a Bad Ignition Switch
  • Happy Thanksgiving Day
  • Pull vs. Push Solenoids
  • What Parts Do I Need To Install A Complete Irrigation System?
  • Tools 1: How to Measure Solenoid's Voltage
  • Guide To Sprinkler Solenoid Valve Repair
  • Welcome To Our Stand , Automechanika Shanghai
  • It's a great Show AAPX 2017!
  • How to Blow Out Your Sprinkler System for Winter with These Easy Instructions
  • Do-it-yourself solutions to irritating irrigation problems
  • Ecectronic shutoff solenoids: Installation.
  • Diesel Engine
  • What does our Research and Development Department do?
  • Preparing the final irrigation plan
  • Sizing pipe and valves and calculating system pressure requirements(2)
  • Huatui Company Travel day Zhu Tan Shan + Furong Gap + Dinghu Peak in Lishui
  • Holiday Notice-HUATUI
  • Sizing pipe and valves and calculating system pressure requirements(1)
  • Irrigation Design 3 - How to Selecting sprinklers and spacing ranges?
  • Irrigation Design 2 - Determining water and power supply
  • Oil Pressure Sensor Replacement for Volvo Truck
  • Determining Irrigation Requirements
  • Why Purchase Irrigation Valve?-Keyopo
  • Diaphragm Valve Disassembly Procedure - Keyopo
Diaphragm Valve Disassembly Procedure - Keyopo
Source:Rember Chan | Author:cynthia | Publish time: 2017-08-29 | 1631 Views | Share:

To inspect the inside of the valve for cleaning or replacement of the diaphragm:

1. Shut off the water at the master shut off valve.

2. Unscrew all bonnet screws if present or unscrew jar-top lid. On some models, the bleed screw and/or flow control knob will also need to be removed.

3. Remove bonnet assembly to expose the spring, diaphragm, and rubber gasket (if any) and filter (if any). Remove and inspect the spring, diaphragm, and rubber gasket for wear or damage. Inspect the diaphragm for clog or a tear in the small hole on its surface.

4. Inspect the valve body for dirt on the diaphragm seat.

5. Inspect the bonnet for dirt clogging the small bleed port near the solenoid.

6. Rinse dirt off if necessary, or use a wire to gently dislodge dirt from the bleed port.

7. Install new diaphragm if necessary. Do not forget to replace the spring. Some new replacement diaphragms are an all-in-one design and do not have a separate rubber gasket to install. Be sure that the holes line up.

8. Press the bonnet firmly back in place. Replace the screws and tighten or screw jar top lid back on.Pressure test the valve to assure that all of the screws are tight enough to prevent any water leakage between the valve body and bonnet.





1. Ensure valve is off with no power going to solenoid.

2. Remove controller wires.

3. Unscrew the solenoid.

4. Check for debris clogging the small port where the solenoid

seats.

5. Rinse off the solenoid to remove debris.

6. Check condition of solenoid O-ring.

7. Replace solenoid if necessary with part number applicable to

your particular model.


上一篇: None
下一篇: Why Purcha......